Answers for overseas buyers, engineers and distributors — from cell structure and test methods to samples, packing and ordering.
Before you request a quote
Most aluminium foam properties depend on relative density and cell structure, so two products with the same name can perform very differently. The most useful information you can send us is: the governing load case or acoustic target, panel dimensions, quantity, surface/finish requirement and the test standard your project uses.
Figures quoted on this site are typical ranges from public technical literature and our own product experience; they are not certified values for a specific batch. Confirmed values are supplied in the datasheet and test report for each order.
Material Basics
What is the difference between open-cell and closed-cell aluminum foam?
Closed-cell foam has isolated gas pores and is normally used for energy absorption, lightweight sandwich cores, thermal insulation and structural protection. Open-cell foam has interconnected pores and is used where fluid flow, filtration, heat exchange or sound absorption is required. Their properties and test methods are different and the two types are not interchangeable.
Is aluminum foam load bearing?
It is a lightweight core and energy absorber, not a replacement for dense structural aluminium. In most designs it is used as the core of a sandwich panel together with face sheets, or as a sacrificial absorber. Bending stiffness comes mainly from the separation of the skins.
Is aluminum foam fire resistant?
The aluminium matrix is non-combustible and does not produce toxic smoke or melting droplets, which is why cellular aluminium is attractive where polymer foams are restricted. Fire classification of a finished assembly still depends on the face sheets, adhesives, coatings and the applicable building code, so the complete build-up must be assessed.
Is aluminum foam recyclable?
The aluminium matrix can be remelted and recycled, which is a significant advantage over polymer foams. Sandwich constructions with adhesives, coatings or dissimilar face sheets need to be disassembled or sorted first, so design for end-of-life separation where possible.
How does aluminum foam compare with aluminium honeycomb or mineral wool?
Honeycomb is a regular, anisotropic two-dimensional cell structure with very high specific stiffness in defined directions. Aluminum foam has an irregular three-dimensional cell structure, is more isotropic, absorbs impact energy through plastic collapse and offers acoustic absorption when opened. Mineral wool is a cheap fibrous absorber but brings moisture sensitivity, fibre shedding and binding-agent ageing. The right choice depends on whether stiffness, energy absorption, acoustics or fire behaviour governs.
Specifications & Testing
What density range can you supply?
Aluminum foam is commonly produced in an apparent density range of roughly 0.2–0.9 g/cm³ (relative density about 0.07–0.35), with porosity around 60–95%. The density you should choose depends on the plateau stress or stiffness your design requires. Tell us the load case and we will recommend a grade.
Can you control the cell size, and do you offer small-cell foam?
Average cell size is controllable through the foaming and solidification conditions; closed-cell products are commonly in the 0.5–10 mm range. Our R&D work with Tsinghua University includes small-cell foam with an average pore diameter of about 1–2 mm and a more uniform pore distribution, which improves mechanical performance. Cell-size distribution should be agreed and checked batch by batch.
Which test standard should we ask for?
For compression behaviour (plateau stress, densification strain, energy absorption) ask for ISO 13314, Mechanical testing of metals — compression test for porous and cellular metals. For sound absorption, ASTM C423 (reverberation room) or ISO 10534-2 / ASTM E1050 (impedance tube) apply to different measurement geometries and their results are not directly comparable. Always request the standard, year, specimen and boundary conditions with the number.
Why do sound absorption coefficients differ so much between suppliers?
Because absorption depends on the test method, the specimen area and mounting, the air cavity behind the panel, the perforation or surface-opening pattern and the frequency range. Compare only values measured with the same method and the same build-up, and ask for the full frequency curve rather than a single NRC figure.
Do your published figures represent guaranteed values?
No. Figures on this site are typical ranges from public technical literature and our own product experience, intended for orientation. Confirmed values for a specific order are those in the agreed datasheet and the batch test report. Market-size estimates in our articles are deliberately quoted with their definitions because different research sources use different scopes.
Processing & Use
Can aluminum foam be cut, drilled, welded or bonded?
Yes — it can be sawn, waterjet cut, milled, drilled, bonded, brazed and laminated with face sheets. Cell walls can collapse under excessive clamping force and cut edges can tear, so dedicated fixtures, sharp tooling and suitable feed parameters are needed. Welding requires care with porosity and oxide layers; bonding or mechanical fixing is often simpler.
How does it behave outdoors, and do you offer corrosion protection?
Aluminium forms a passive oxide film, but the large internal surface of a porous structure can retain moisture and salts and is susceptible to crevice or galvanic corrosion. For exterior or marine environments we recommend surface treatment, sealing, compatible coatings and avoiding direct contact with dissimilar metals. Confirm the environment at enquiry stage.
Can the panels be coloured, perforated or backlit?
Yes. Colour coating, anodising, painting, perforation, surface opening and backlighting are used for architectural panels and light-transmitting sheets. Ask for a sample of the actual finish, since the cellular texture changes how colour and light read.
Ordering & Samples
Can you make sandwich panels with our specified face sheets?
Yes. Foam cores can be combined with aluminium or other face sheets by adhesive bonding, brazing or mechanical assembly, with specified thickness, layup and edge treatment. Send your panel drawing, stiffness target and environmental conditions.
Do you provide samples, datasheets and test reports?
Samples, product datasheets, compression test data and third-party inspection can be arranged for qualified projects. Please state the grade, dimensions and the test standard you need so the sample and the report match your approval process.
What information should be included in an enquiry?
The application, governing load case or acoustic target, target density or plateau stress, panel dimensions and tolerances, quantity, surface / finish requirement, applicable test standard and destination port. Drawings are always helpful. This lets us quote a defined specification instead of a generic product.
How is aluminum foam priced and packed for export?
Because density and specification vary widely, quotations must state whether the price is per m³, per m², per kg or per piece, together with the corresponding density and tolerances. Panels are normally protected at the edges and faces, packed in wooden crates or pallets suitable for sea or air freight. Confirm the Incoterm and packing requirement with your order.
What are typical lead times and minimum order quantities?
These depend on the grade, whether tooling or composite layup is involved, and the quantity. We do not publish a fixed MOQ or lead time on this site — send your specification and we will confirm current sample and production lead times for your case.
Have an aluminum foam project to discuss?
Send us your drawing, density target or performance requirement. Our engineers will get back with a proposal.